Durodyne
 

 

 

 

Cable

Wire Rope

Aviation grade galvanized wire rope supplied by Duro Dyne is manufactured to exacting standards and statistically tested to verify stated breaking strengths. Duro Dyne WC2-CL6, WC3-CL12 and WC4-CL18 wire ropes utilize standard 7x7 construction. Duro Dyne WC8-CL25 and WC6-CL23 wire ropes have a 7x19 construction. Only use wire rope supplied by Duro Dyne with Dyna-Tite cable locks to ensure maximum safety and integrity of the installation.

Image 2

Size
Tolerance
Construction
For Use With Safe Working
Load*+
WC8-CL25
+5%/-0%
7x19
CL25-WC8

50-1,100 lbs.
(25-500 kg)

WC6-CL23
+.018/-.009 inch
7x19
CL23-WC6

50-640 lbs.
(25-291 kg)

WC4-CL18
+.014/-.007 inch
7x7
CL18-WC4

25-250 lbs.
(12-114 kg)

WC3-CL12
+.012/-.006 inch
7x7
CL12-WC3

25-150 lbs.
(12-68 kg)

WC2-CL6
+.010/-.005 in.
7x7
CL6-WC2

10-75 lbs.
(5-34 kg)

*Safe Working Loads are based on a 5:1 Safety Factor.

+Hanging at angles will reduce the Safe Working Loads. Please see our ‘Effects of Hanging at Angles’ table at: www.durodyne.com/DTTesting.php

Wire Rope Submittal >

 

Looped Cable Assembly

The Looped Cable Assembly enhances the Dyna-Tite suspension system by the addition of a pre-looped cable end. Once the wire rope is pulled around the anchor point and through the looped end of the cable, it is already secured at one end, saving time at the jobsite. The remaining wire rope “drop” is passed through a channel in the Dyna-Tite Cable Lock. Then, the wire rope is either wrapped around the ductwork or inserted through a fastening point and back up into the second channel of the same cable lock. The locking teeth inside the cable lock engage the wire rope which secures the ductwork in place. To ensure maximum safety, use only looped wire rope supplied by Duro Dyne with all cable lock
applications.

Image 2

Wire Rope Size
Length
Loop Size
WC2-CL6
5 ft
1-1/2''
WC2-CL6
10 ft
1-1/2''
WC2-CL6
15 ft
1-1/2''
WC2-CL6
25 ft
1-1/2''
WC3-CL12
5 ft
1-1/2''
WC3-CL12
10 ft
1-1/2''
WC3-CL12
15 ft
1-1/2''
WC3-CL12
25 ft
1-1/2''
WC4-CL18
5 ft
1-1/2''
WC4-CL18
10 ft
1-1/2''
WC4-CL18
15 ft
1-1/2''
WC4-CL18
25 ft
1-1/2''

End Fixings Installation Instructions >

 

 

Eyelets

Duro Dyne Dyna-Tite eyelets are manufactured of zinc plated cold rolled steel and swaged to the wire rope cable with a hydraulic press. Dyna-Tite Eyelet assemblies are available for installation with either a 1/4 in. or 3/8 in. fastener. They are available in 45°, 90° and straight variations and can also be purchased as a package with the appropriate cable lock.

Eyelets Lit Sheet >

Eyelet Kits Lit Sheet >

End Fixings Installation Instructions >

90° Eyelet Submittal >

45° Eyelet Submittal >

Straight Eyelet Submittal >

 

 

Snap Hooks

Snap hook cables offer easy attachment points and are ideal for applications that require constant inspection or maintenance that may require you to remove the load from the ceiling.

Snap Hook Lit Sheet >

Snap Hook Submittal >

 

 

Dyna-Stud® Swaged Threaded Stud

Dyna-Studs used with Dyna-Tite cable locks can greatly decrease labor time for constructing suspension systems from a concrete or steel structure.

The Swaged Dyna-Stud is a heavy duty stud with one end of an aircraft rated cable attached. Dyna-Stud is used to suspend duct work from a concrete structure. The stud is threaded into the expansion anchor without putting stress on the cable. This makes for a much safer and tighter connection. The raw end of the cable, in conjunction with the cable lock, is used to attach the object being supported.

• Available with:
1/4 Threaded Bolt and WC3-CL12 Wire Rope
3/8 Threaded Bolt and WC4-CL18 Wire Rope or
3/8 Threaded Bolt and WC4-CL18 Wire Rope with Zip-Clip Lock
• Available in 5, 10, 15 and 25 ft lengths
• Drop-ins sold seperately
• Safe Working Loads are based on a 5:1 Safety Factor


Dyna-Stud Swaged Lit Sheet >

Dyna-Stud Swaged Submittal >

Dyna-Stud Swaged with Zip-Clip Submittal >

End Fixings Installation Instructions >

 


 

Cable Cutter

When cutting wire cable it is important to use a recognized wire cable cutter such as the Duro Dyne cutter detailed here. This will ensure that the form of the rope is maintained prior to insertion in the Dyna-Tite.

▪Safety Catch
▪Hand held cutting tool for WC2-CL6, WC3-CL12, WC4-CL18 and WC6-CL23 Wire Rope.
▪Spring Loaded For Ease Of Use
▪5” Long Handles For High Leverage
▪Hardened Steel Blades For Durability
▪Vinyl Coated Handles For Comfortable, Non-Slip Grip

Image 2

 

 

WC8-25 Cable Cutter

When cutting wire cable it is important to use a recognized wire cable cutter such as the Duro Dyne cutter detailed here. This will ensure that the form of the rope is maintained prior to insertion in the Dyna-Tite.

▪ Safety Catch
▪ WC8-CL25 Wire Rope Cutting Capacity
▪ Hardened Steel Blades For Durability
▪ Vinyl Coated Handles For Comfortable, Non-Slip Grip

Image 2

 

 

Cable Counter

The CCC1 makes preparing for your duct hanging project a lot simpler. Take an empty five gallon bucket, put a spool of wire rope in the bottom, put in some boxes of Dyna-Tite cable locks and a cable cutter. Place the CCC1 on top of the bucket and you are ready for the job site. At the job site remove the cable lock boxes and the wire cutter, thread the wire rope through the CCC1 measuring device and you are ready to hang ductwork. Just pull the wire rope to the length needed, cut it and reset the counter.

▪Counter displays from 0 feet 0 inches to 9999 feet and 11 inches
▪Push Button Reset
▪Designed For Use With Duro Dyne Wire Rope
▪Fits most 5 gallon buckets
▪Lightweight

Image 2

 

 

 

 

 

Image 2
Dyna-Tite Product Catalog >

Image 2
Dyna-Tite Engineer Binder >

Please be patient when downloading the Engineer Binder.

 

 
See Our Video